Polythene and polyethylene sheet.

Wednesday, December 15, 2010

Polythene or polyethylene sheet is commonly used as a damp-proof membrane with oversite concrete for all but severe conditions of dampness. It is recommended that the sheet should be at least 0.25 mm thick (1200 gauge). The sheet is supplied in rolls 4 m wide by 25 m long. When used under concrete oversite the sheet should be laid on a blinding layer of sand or compacted fuel ash spread over the hardcore.

The sheets are spread over the blinding and lapped 150 mm at joints and continued across surrounding walls, under the dpc for the thickness of the wall.

Where site conditions are reasonably dry and clean, the overlap joints between the sheets are sealed with mastic or mastic tape between the overlapping sheets and the joint completed with a
polythene jointing tape as illustrated in Fig. 29.

For this lapped joint to be successful the sheets must be dry and clean else the jointing tape will not adhere to the surface of the sheets and the joint will depend on the weight of the concrete or screed pressing the joint sufficiently heavily to make a watertight joint. As clean and dry conditions on a building site are rare, this type of joint should be only used where there is unlikely to be heavy absorption of ground moisture.
Where site conditions are too wet to use mastic and tape, the joint is made by welting the overlapping sheets with a double welted fold as illustrated in Fig. 30, and this fold is kept in place by weighing it down with bricks or securing it with tape until the screed or concrete has been placed. The double welt is formed by folding the edges of sheets together and then making a welt which is flattened.

The plastic sheet is effectively impossible to fold and so stiff and elastic that it will always tend to unfold so that it requires a deal of patience to fold, hold in place and then contrive to fold along the joint. By using the maximum size of sheet available it is possible to minimise the number of joints.

The sheet should be used so that there are only joints one way as it is impractical to form a welt at junctions of joints.

Where the level of the damp-proof membrane is below that of the dpc in walls it is necessary to turn it up against walls so that it can overlap the dpc or be. turned over as dpc as illustrated in Fig. 31. To keep the sheet in place as an upstand to walls it is necessary to keep it in place with bricks or blocks laid on the sheet against walls until the concrete has been placed and the bricks or blocks removed as the concrete is run up the wall.

At the internal angle of walls a cut is made in the upstand sheet to facilitate making an overlap of sheet at corners. These sheets which are commonly used as a damp-proof membrane will serve as an effective barrier to rising damp, providing they are not punctured or displaced during subsequent building operations.

Fig. 29 Jointing laps in polythene sheet.




Fig. 30 Double welted fold joint in polythene sheet.



 Fig. 31 Damp-proof membrane turn up.

Related Posts by Category:




16 comentarios:

Unknown said...

Polyethylene sheet is the most common vapor barrier material for concrete slabs and is very resistant to harmful chemicals. It is very useful for simple material construction and to large industrial improvisation. But putting the sheet in concrete is a very tricky process. Utmost care should be done to ensure that it was properly glued to the material. Before putting the sheet, clean the surface of the material and select your adhesive. Pressure sensitive types of adhesive are formulated from rubber and create a strong bond. Using a glue roller, cover the back of polyethylene sheet with adhesive and press it onto the surface of the concrete. Apply pressure with your hand to ensure proper contact with the material.

can any supplier of pe sheet pm me? topnotchwaterproofing@gmail.com

Unknown said...

i just say this is very nice article i really like it and bookmark this article. You did excellent job.

Thanks and Regards
sell chemical

Unknown said...

If you've never used stretch film before or aren't happy with the film you're using, how do you know which one is right? Following are 6 considerations for choosing the best stretch film for the job.
see more details:ellipsometry

tiger shrof said...
This comment has been removed by the author.
jade said...

a bought design when the shirt didn't fit. I had to use double-faced pellon to reattach it to a new shirt. corrugated plastic sheets

Unknown said...


Impressive blog! Thank you for sharing this worthy information with us.
Custom Corrugated Plastic


Unknown said...

Polyethylene sheeting is a plastic film made from petroleum. That is why the price of the product can vary depending on what oil prices are doing.Colored Corrugated Cardboard Rolls

Unknown said...

You wouldn't believe how much this side of the bag can hold, even though the bag is not that large. I emptied out this side to show you (below). coroplast sheets suppliers

jade said...

We have state-of-art mfg facilities with Hi-tech German, Italian and Korean machineries for assured Quality Products........polypropylene corrugated sheets suppliers,http://www.jx-plastic.com/polypropylene_sheets_4x8_292.html........

Unknown said...

for more suppliers you can visit corrugated plastic sheets suppliers

Jones Morris said...

corrugated plastic sheets are the Ideal  material for many industries including construction , signs, advertising, graphics display, screen printing, Packaging& shipping, Arts& crafts. China corrugated plastic sheets manufacturers

Unknown said...

Can anyone advise me on if thick dpm used under concrete can it be used as a gas membrane..

Unknown said...

Can a polythene sheet used over the block before casting the concrete affect a story building?

Abdul Suraj said...

Nice information on here, I would like to share with you all my experience trying to get a loan to expand my Clothing Business here in Malaysia. It was really hard on my business going down due to my little short time illness then when I got heal I needed a fund to set it up again for me to begin so I came across Mr Benjamin a loan consultant officer at Le_Meridian Funding Service He asked me of my business project and I told him i already owned One and i just needed loan of 200,000.00 USD he gave me form to fill and I did also he asked me of my Valid ID in few days They did the transfer and my loan was granted. I really want to appreciate there effort also try to get this to anyone looking for business loan or other financial issues to Contact Le_Meridian Funding Service On Email: lfdsloans@lemeridianfds.com / lfdsloans@outlook.com He also available on WhatsApp Contact:+1-9893943740.

Nadia Albert said...

Are you looking for a business loan, personal loans, mortgage loans, car loans, student loans, unsecured loans for consolidation, project finance etc ... Or simply refuse loans from a bank or financial institution for one or more reasons? We are the right solutions for credit! We offer loans to companies and individuals with a low and affordable 2% interest rate. Therefore, if you are interested in an urgent and secured loan. For more information, please email us today: Via: Elegantloanfirm@hotmail.com.

Post a Comment

 
 
 

Labels